HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY RISK MANAGEMENT & SAFETY
|
|
|
- Alison Stevens
- 6 years ago
- Views:
Transcription
1 HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY RISK MANAGEMENT & SAFETY
2 WHAT IS HOT WORK? WORK INVOLVING BURNING, WELDING, OR A SIMILAR OPERATION THAT IS CAPABLE OF INITIATING FIRES OR EXPLOSIONS.
3 EXAMPLES OF HOT WORK Welding, open-flame soldering, brazing, thermal spraying, oxygen/arc cutting Heat treating Grinding Thawing pipe Powder-driven fasteners Hot riveting Similar applications producing spark, flame, or heat
4 WHAT IS EXCLUDED? Candles Pyrotechnics Cooking operations Electric soldering irons
5 Hot work permits are used to lessen the chances of fires breaking out by making sure only qualified individuals are doing the work in a safe area and a safe manner. PURPOSE
6 SCOPE This program applies to Auburn University employees and contractors who perform or supervise hot work activities in existing University buildings. This program does not apply to areas that are specifically designed and equipped for such operations, e.g., designated welding areas.
7 Hot work should not be performed if the work can be avoided or performed in a safer manner. When practical, objects to be welded, cut, or heated must be moved to a designated safe location, e. g., designated welding areas. PROCEDURES
8 PROCEDURES If hot work must be performed, a Hot Work Permit must be obtained from Auburn University s Department of Risk Management & Safety before the hot work begins.
9 All precautions on the Hot Work Permit must be met prior to performing any hot work. The Hot Work Permit will be issued by Risk Management & Safety and is valid only for the date(s) and time specified on the permit. A copy of the permit must remain at the hot work location until the hot work is completed. PROCEDURES
10 PROCEDURES All personnel (employees, contractors, building occupants)must be suitably protected against hazards generated by the work(e. g., heat, sparks, fumes, welding rays, etc.) This may include, but is not limited to, the use of personal protective equipment, shields, screens, or local exhaust ventilation.
11 PROHIBITED CONDITIONS A Hot Work Permit will not be issued if any of the following conditions exist: Combustible or flammable materials are within 35 feet and cannot be moved or protected. Floor and wall openings cannot be covered. Cutting or welding on pipes or other metals can conduct enough heat to ignite nearby combustible materials. Any condition that could result in undue hazards by performing the work.
12 MANAGEMENT RESPONSIBILITIES Advise all contractors about site-specific flammable materials, hazardous processes, and other fire hazards. Ensure all individuals, including contractors, are aware of inherent risks involved and emergency procedures. Ensure hot work procedures are being followed. Ensure that contractors follow University procedures. Hot work only in areas permitted by PAI.
13 PERMIT-AUTHORIZING INDIVIDUALS (PAIs) Responsibilities: Determine site-specific flammable materials, hazardous processes, other potential fire hazards present or likely in work location. Ensure fire protection and extinguishing equipment properly located at site. Ensure fire watch available on site.
14 SUPERVISOR RESPONSIBILITIES Ensure that all employees and contractors are following hot work procedures. Ensure that a hot work permit is issued prior to the start of work. Ensure that all cutting and welding equipment is in good condition. Ensure that all employees are suitably trained in the operation of the equipment and safe use of the process. Ensure that contractors follow University procedures. Includes outage procedures for fire alarm and sprinkler.
15 EMPLOYEE RESPONSIBILITIES Follow and use hot work procedures. Obtain a hot work permit prior to starting work. Ensure that all cutting and welding equipment is in satisfactory condition and in good repair. Attend and actively participate in training sessions. Protect nearby personnel and passers by against heat, sparks, etc. when working in occupied buildings. Use PPE as required.
16 FIRE WATCH TRAINED PERSONNEL WHO ARE IN ATTENDANCE DURING THE ENTIRE HOT WORK OPERATION AND ARE IMMEDIATELY AVAILABLE TO EXTINGUISH A FIRE OR TAKE OTHER EFFECTIVE ACTION IF NEEDED.
17 WHEN IS A FIRE WATCH REQUIRED? Wall or floor openings within 35 feet of the work expose combustibles in adjacent areas including confined spaces. Combustibles could be ignited by conduction or radiation through metal partitions, walls, ceilings, or roofs. Anytime hot work is conducted.
18 FIRE WATCH RESPONSIBILITIES Awareness of inherent hazards of work site and hot work. Ensure safe conditions maintained during hot work. Authority to stop operations if unsafe conditions develop. Ensure proper fire extinguishing equipment is readily available & be trained in it s use. Familiar with facilities and procedures for sounding alarm in event of fire.
19 FIRE WATCH RESPONSIBILITIES Watch for fires in all exposed areas. May extinguish fires contained to a small area. Sound alarm when appropriate. Call 911. Maintain watch at least ½ hour after hot work has been completed.
20 REQUIREMENTS FOR HOT WORK PERMIT Equipment is in good operating condition. Floor free of combustible materials (paper clippings, wood shavings, textile fibers, etc.) for radius of 35 ft. Combustible floors (except wood on concrete) Kept wet Covered with damp sand
21 REQUIREMENTS FOR HOT WORK PERMIT Combustibles relocated at least a 35 ft. radius from work area. If not feasible, one of the following: Protected with fire-retardant covers. Shielded with metal or fire-retardant guards/curtains. Edges of covers at floor.
22 REQUIREMENTS FOR HOT WORK PERMIT Openings or cracks in walls, floors, ducts within 35 ft. of site must be tightly covered with fire-retardant or noncombustible material. Conveyor systems shielded. Work near walls/partitions/ceilings/roofs of combustible construction must be protected by fireretardant shields/guards. Work on wall/partition/ceiling/roof requires fire watch on both sides to prevent ignition of combustibles.
23 REQUIREMENTS FOR HOT WORK PERMIT Fully charged/operable fire extinguishers of appropriate type available in immediate work area. If close to sprinkler head or smoke/heat detector an outage must be requested. Outages require 5 days notice unless it is an emergency.
24 REQUIREMENTS FOR HOT WORK PERMIT Nearby personnel suitably protected against heat, sparks, slag, etc. Permit length determined by PAI but no more than one week. PAI inspect at least once per day while permit in effect.
25 RMS FIRE SAFETY CONTACTS MaryAnn May Fire & Life Safety Specialist Jon Haney Fire & Life Safety Specialist Patricia Davis Fire & Life Safety Technician Risk Management & Safety ms/#/
HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY SAFETY AND HEALTH RISK MANAGEMENT AND SAFETY
HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY SAFETY AND HEALTH RISK MANAGEMENT AND SAFETY WORK INVOLVING BURNING, WELDING, OR A SIMILAR OPERATION THAT IS CAPABLE OF INITIATING FIRES OR EXPLOSIONS. WHAT IS
Hot Work Program. Purpose of Procedure:
BGSU Hot Work Program Page 1 Bowling Green State University Purpose of Procedure: Hot Work Program These procedures have been established to comply with Ohio s Public Employee Risk Reduction Act, the OSHA
Hot Work Program June 2017
Hot Work Program June 2017 Hot Work Program TABLE of CONTENTS I. General Information II. Definitions III. Roles and Responsibilities IV. Hot Work Areas V. Hot Work Permit VI. Hot Work Permit-Not Required
RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM
RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM REV 12/99 1 TABLE OF CONTENTS HOT WORK PERMIT PROGRAM A. Purpose and Scope.3 B. Hot Work Permit Procedures...3 C. Hot Work Permit - Prohibited Conditions...4
RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM
RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM REV 10/2015 TABLE OF CONTENTS HOT WORK PERMIT PROGRAM Contents A. PURPOSE AND SCOPE... 3 B. HOT WORK PERMIT PROCEDURES... 3 C. HOT WORK PERMIT PROHIBITED CONDITIONS:...
Areas that have been designed and constructed for performing open-flame or spark-producing work.
PURPOSE Baylor University recognizes that there is a potential for injury to people and damage to property that can result from fire or sparks that arise when hot work is performed outside of a designated
Desert Research Institute Hot Work Permit Program
1.0 INTRODUCTION 1.1 PURPOSE The purpose of this policy is to prevent any fires that may result from hot work processes. 1.2 SCOPE 1.2.1 For the purposes of this policy, hot work is defined as any temporary
HOT WORK MANAGEMENT PROGRAM
HOT WORK MANAGEMENT PROGRAM Rose-Hulman Institute of Technology Table of Contents SECTION 1.0 Purpose 2.0 Regulatory Reference 3.0 Scope 4.0 Elements of the Program 5.0 Responsibility 6.0 Training and
University of Central Missouri Hot Work Permit Program
1. Introduction University of Central Missouri Hot Work Permit Program The University of Central Missouri's (UCM) Hot Work Program is designed to minimize risks to our campus community, which includes
MCW s Hot Work Permit Program
2019 MCW s Hot Work Permit Program - Hot Work/Fire Watch Operations This document is the Medical College of Wisconsin s (MCW) written program for conducting hot work, and identifies roles and responsibilities
Hot Work Program. Program Origination: October, 2017
Hot Work Program Program Origination: October, 2017 Contact Personnel: Jason Kayser, Fire & Safety Specialist Jason.kayser@uni.edu 319-273-2004 Hot Work Program UNI Employees & Contractors October, 2017
HOT WORK PROGRAM OSHA
HOT WORK PROGRAM 1910.252 OSHA Table of Contents Purpose... 3 Definitions... 3 Responsibilities... 3 Hot Work Permitted Locations... 5 Fire Prevention Precautions... 5 Personal Protective Equipment...
Hot Work Permitting Procedure
Hot Work Permitting Procedure Purpose Audience Policy This procedure is designed to ensure that spark and flame producing construction and maintenance activities do not present an undue fire hazard to
Guide to Hot Work NFPA 51B Understanding the new requirements after July 1, 2018
Guide to Hot Work NFPA 51B Understanding the new requirements after July 1, 2018 What is the issue that caused the change? Unpermitted hot work was determined to be the cause of a fire that killed two
Environmental, Health and Safety. UNC Charlotte Hot Work Program (Welding, Cutting, and Brazing)
Environmental, Health and Safety UNC Charlotte Hot Work Program (Welding, Cutting, and Brazing) January 2014 TABLE OF CONTENTS PURPOSE:... 2 SCOPE:... 2 HOT WORK RESPONSIBILITIES... 2 SPECIFIC DEPARTMENTAL
Roger Williams University Hot Work Plan
Roger Williams University Hot Work Plan Roger Williams University Dept. Of Environmental Health and Safety One Old Ferry Road Bristol, RI 02809 Adopted: April 26, 2011(President s Cabinet) Roger Williams
HOT WORK SAFETY GUIDE. Specific responsibilities relating to hot work operations are outlined below.
HOT WORK SAFETY GUIDE Version Date Comments 5 March, 2012 Revised document 6 June, 2015 Update code citation - SFPC 2012 A. INTRODUCTION The purpose of this Guide is to provide information regarding welding
SUNY Geneseo ENVIRONMENTAL HEALTH & SAFETY
Revision No.: 1 Page 1 of 7 I. PURPOSE The purpose of this policy is to establish minimum standards for safely conducting hot work tasks to help mitigate hazards that could occur during hot work operations.
Hot Work Permit Program
Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0 Training.. 5 5.0 Recordkeeping. 5 6.0 Permits
General Hot Work Program Guidelines. Lyndsey Beaudin
General Hot Work Program Guidelines Lyndsey Beaudin WHY SUCH A HOT TOPIC? NEW YORK STATE OFFICE OF FIRE PROTECTION AND CONTROL Violation: Hot Work Permit not issued for Hot Work Area 2603.4 Hot Work Program
The Ohio State University. Hot Work Permit Program (Welding, Cutting and Brazing)
Environmental Health & Safety 1314 Kinnear Rd. Columbus, Ohio 43212 Phone (614) 292-1284 Fax (614) 292-6404 http://www.ehs.osu.edu/ The Ohio State University Hot Work Permit Program (Welding, Cutting and
Hot Work Program. Roles and Responsibilities. Management. PAI Responsibilities
Hot Work Program Scope is aware of the hazards associated with hot work operations (cutting, welding, brazing and soldering, grinding, etc.) is committed to keeping our employees safe and to control hazards
Non Electrical Hot Work Program
Environmental Health and Safety Name: Non Electrical Hot Work Program Date Created: 02/18/2014 Date Revised: Created By: Bob Happel PURPOSE The purpose of this Program is to protect people and property
IWU PHYSICAL PLANT SAFETY PROGRAM
STANDARDS Welding, Cutting and Brazing/General Requirements OSHA 1910.252, 1. Purpose Hot work is any temporary or permanent operation involving open flames or producing heat and/or sparks. This includes
DUQUESNE UNIVERSITY HOT WORK PROGRAM
DUQUESNE UNIVERSITY HOT WORK PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Responsibilities 2 General Requirements 2 Welding or Cutting Containers
HOT WORK PERMIT PROGRAM REVISED AND DISTRIBUTED BY: THE UNIVERSITY OF VERMONT DEPARTMENT OF PHYSICAL PLANT TRAINING & COMPLIANCE OFFICE
University of Vermont Department of Physical Plant Burlington, Vermont HOT WORK PERMIT PROGRAM REVISED AND DISTRIBUTED BY: THE UNIVERSITY OF VERMONT DEPARTMENT OF PHYSICAL PLANT TRAINING & COMPLIANCE OFFICE
Public Input No. 17-NFPA 51B-2015 [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document
![Public Input No. 17-NFPA 51B-2015 [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document](/thumbs/89/99212691.jpg "Public Input No. 17-NFPA 51B-2015 [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document")
of 55 11/18/2016 2:12 PM Public Input No. 17-NFPA 51B-2015 [ Global Input ] 3.3.X Responsible Party. The building owner, a lessee, or a duly authorized representative. Globally change "management" everywhere
SAFETY AND HEALTH STANDARD HOT WORK PERMIT Effective Date: 06/10/10 Standard: 16.1 Document Number: KUCSH0040 Rev: 04
16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to prevent the inadvertent ignition of combustible materials when performing hot work. 16.1.2 DEFINITIONS 16.1.2.1 Hot work - includes welding,
Hot Work Safety Program
Hot Work Safety Program 6900-2.0 Associated OHS Process: General Industry & Construction Safety The master copy of this document resides in electronic format. Printed copies of this document are for convenience
University Environmental Health and Safety. Hot Work Permit Program
University Environmental Health and Safety Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0
(WELDING, CUTTING, AND OPEN FLAME WORK)
THE UNIVERSITY OF TEXAS AT TYLER Hot Work (WELDING, CUTTING, AND OPEN FLAME WORK) Program 2016 Table of Contents 1. INTRODUCTION... 3 2. PURPOSE... 3 3. APPLICATION... 3 4. DEFINITIONS... 3 5. PROGRAM
Hot Work Permit Program
Environmental Health and Safety Office Hot Work Permit Program Permitting Process for welding, cutting and brazing. Adopted: March 6, 2007 Revised: 7/18/16 http://www.stlawu.edu/environmentalhealth-and-safety/environmental-healthand-safety-policies
Hot Work Permit Guidelines
2408 Wanda Daley Drive Ames, Iowa 50011-3602 (515) 294-5359 www.ehs.iastate.edu Copyright 2014 Reviewed 2015 2 Hot Work Permit Guidelines Directory of Service and Emergency Providers Services Environmental
Hot Work Policy & Procedure
Hot Work Policy & Procedure Policy: Reference: The purpose of the PCS General Contractor Hot Work policy is to protect personnel and property from a fire caused by hot work. The PCS Hot Work procedure
Hot Work Procedures. Competent means possessing knowledge, experience and training to perform a specific duty.
Hot Work Procedures Purpose This procedure will provide the knowledge and equipment required to minimize the identified workplace hazards associated with Hot Work. These procedures will provide: information
University of Nevada, Reno
University of Nevada, Reno HOT WORK PERMIT PROGRAM Program Contact Person: John A. Braun, CSP Environmental Health and Safety University of Nevada, Reno Phone: 775-784-6478 HOT WORK PERMIT PROGRAM UNIVERSITY
OFFICE OF STATE HUMAN RESOURCES
OFFICE OF STATE HUMAN RESOURCES NUMBER: HWP-1 TOTAL PAGES: 6 SUBJECT: Hot Work Program Effective Date: Revision Date: Revision #: RELATED LEGISLATION: This program outlines procedures for [Agency/University]
TAMPA ELECTRIC COMPANY ENERGY SUPPLY HOT WORK PERMITTING PROGRAM
TABLE OF CONTENTS TITLE PAGE # PURPOSE / INTRODUCTION 1 RESPONSIBILITY 2 EMPLOYEE TRAINING AND DOCUMENTATION 3 PROGRAM REQUIREMENTS 4 HOT WORK PERMIT PLANNING AND PRECAUTIONS 4 6 FIREWATCH 6, 7 HOT WORK
PURPOSE:... 3 EMPLOYEE CLASSIFICATIONS:... 3 OUTSIDE PERSONNEL (I.E., CONTRACTORS):... 4 HOT WORK REQUIREMENTS:... 4 EMPLOYEE TRAINING:...
South Central College North Mankato/Mankato Campus 1920 Lee Boulevard N. Mankato, MN 56002-1920 Faribault Campus 1225 Third Street SW Faribault, MN 55021-5782 Adoption Date: 09-18-15 Revision Date: 02-23-17
Hot Work and Welding Management Procedures Attached to FIN-INS Introduction. 1.1 Purpose
1. Introduction 1.1 Purpose Hot Work and Welding Management Procedures Attached to FIN-INS-22 Indiana University Insurance, Loss Control and Claims (INLOCC) and Indiana University Environmental Health
Prevention of Hot Work Fires in Healthcare Facilities. Sherie Van Slyke Engineering Specialist
Prevention of Hot Work Fires in Healthcare Facilities Sherie Van Slyke Engineering Specialist Are hot work fires common in hospitals? What is hot work? Hot work statistics The contractor component. Construction
STANDARD PROCEDURE INSTRUCTION
STANDARD PROCEDURE INSTRUCTION Title SPI Department Hot Work Permit Supersedes SPI Dated # 34-3 Effective Date Safety, Health and Environment Dec 22, 2014 Jan 19, 2016 Hot Work Permit 1. PURPOSE 1.1 To
Hot Work Permit Program
Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0 Training.. 5 5.0 Recordkeeping. 5 6.0 Permits
University of Delaware.
HOT WORK PERMIT PROGRAM The following information describes the code required Hot Work Permit Program at the University of Delaware. PART 1 GENERAL University Contact: Department of Environmental Health
KENNECOTT UTAH COPPER
16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to define the requirement for performing hot work operations on certain components of machinery, equipment and structures and preventing the
HOT WORK PROGRAM October 2016
HOT WORK PROGRAM October 2016 A. SCOPE AND APPLICATION The UNLV Hot Work Program is established in accordance with the standards listed in Section H and specifies the requirements and procedures necessary
Hot Work Permitting Program
Hot Work Permitting Program Environmental Health, Safety, and Risk Management Department Box 6113, SFA Station Nacogdoches, Texas 75962-6113 Original: January 2004 Revised: January 2011, April 2018 Table
Risk Control Guide HOT WORK
HOT WORK RCG003 (E)-v2-01/2017 Page 1 2017 Royal & Sun Alliance Insurance plc Introduction Hot work is defined as any operation that involves open flames or produces heat or sparks, e.g. cutting, grinding,
Hot Work Safety and the Permitting Process. Leaders Guide and Quiz
! Hot Work Safety and the Permitting Process Leaders Guide and Quiz 4879 INTRODUCTION TO THE PROGRAM Structure and Organization Information in this program is presented in a definite order so that employees
HOT WORK GUIDELINES 3. MANDATORY AREAS REQUIRING HOT WORK PERMITS Within the Service Station Site
1. GENERAL This procedure gives guidelines for the precautions and preparation that should be followed to ensure that work covered by a hot work permit can be carried out safely without risk to people
Fire Safety & Hot Work Permits. Oakland University Office of EH&S
Fire Safety & Hot Work Permits Oakland University Office of EH&S Topics of Discussion Why do we Need a Hot Work Permit Real-life Cutting/Welding Accidents When is a Hot Work Permit Required Hot Work Precautions
Villanova University Department of Environmental Health and Safety Policy and Procedure Manual
Villanova University Department of Environmental Health and Safety Policy and Procedure Manual Subject: Hot Works Procedure Number: S15 Effective: 20 Apr 99 Revised: 9-15-15 I Purpose: To establish a procedure
Hot Work Program. SUNY Canton. Purpose
SUNY Canton Hot Work Program Purpose Hot Work is defined as welding, thermite welding, thermal spraying, installation of torch applied roof systems, cutting, soldering, brazing, grinding, thawing pipe
Fire caused by Hot Works. A guide to loss prevention
Fire caused by Hot Works A guide to loss prevention Hot Work is usually defined as any open flame, spark or heat producing activity and is typically associated with cutting, welding, grinding and brazing
"HOT WORK SAFETY AND THE PERMITTING PROCESS"
PRESENTER'S GUIDE "HOT WORK SAFETY AND THE PERMITTING PROCESS" Part of the "SAFETY MEETING KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE
This program applies to University faculty, staff, students, vendors, or contractors performing Hot Work on behalf of the University of Iowa.
University of Iowa Hot Work Loss Prevention Program This program has been approved for use at the University of Iowa and will remain in effect until a revised program is developed and approved. Written:
DRAFT Hot Work Procedure South Shore Regional School Board
Hot Work Procedure South Shore Regional School Board SSRSB Hot Work Procedure - 2010 Page 1 of 12 Introduction DRAFT Hot work comes in a variety of applications each with its own heat source severity.
Program Title Hot Work Program. Classification Fire Safety and Emergency Response. Program No INTRODUCTION
1.0 INTRODUCTION ENVIRONMENTAL HEALTH AND SAFETY PROGRAM MANUAL As part of the Weill Cornell Medical College (WCMC) Environmental Health and Safety (EHS) Program Manual, this has been established. The
Fire safety basics for hot work operatives. CFPA-E Guideline No 12:2012 F
Fire safety basics for hot work operatives CFPA-E Guideline No 12:2012 F FOREWORD The European fire protection associations have decided to produce common guidelines in order to achieve similar interpretation
RISKTOPICS. DISCUSSION For the purposes of this document, hot work: Management practices: Hot work Property and Business Interruption January 2013
RISKTOPICS Management practices: Hot work Property and Business Interruption January 2013 This document highlights the property conservation responsibilities of those who utilize hot work outside of areas
HOT WORK SAFETY GUIDELINE
HOT WORK SAFETY GUIDELINE SAFETY GUIDELINE 2017 1 Hot work safety guideline Index 1 Hot work training... 2 2 Purpose of the safety guidelines... 2 3 Binding force of the safety guidelines... 2 4 Definitions...
Loss Prevention Standards
Introduction A hot work management system and associated permit is a formal recorded process used to help control work which is identified as potentially hazardous, and is an important part of an organisation
Hot Work Procedure. Work Health and Safety Policy Responsible Officer. Executive Director, Infrastructure Services and Development Approved by
Hot Work Procedure Related Policy Work Health and Safety Policy Responsible Officer Executive Director, Infrastructure Services and Development Approved by Executive Director, Infrastructure Services and
Hot Work. Approved by: Ruth Hampton Review Date: 6 th December 2015
5 WHS PROCEDURE P28-01 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment for all persons
Making sense of risk Risk engineering. Marine hot work Permit to Work (PTW) systems
Marine hot work Permit to Work (PTW) systems Marine hot work Permit to Work (PTW) systems Hot work is any operation involving open flames or producing heat and/or sparks, including but not limited to welding,
KENNECOTT UTAH COPPER
16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to define the requirement for performing hot work operations on certain components of machinery, equipment and structures and preventing the
M E M O R A N D U M. NFPA 51B First Draft Technical Committee FINAL Ballot Results (A2018)
National Fire Protection Association 1 Batterymarch Park, Quincy, MA 02169-7471 Phone: 617-770-3000 Fax: 617-770-0700 www.nfpa.org M E M O R A N D U M TO: FROM: Technical Committee on Hot Work Operations
RC 7 V2 3/12/07 3:41 am Page 1 RC7 for hot work
for hot work RC7 LOSS PREVENTION RECOMMENDATIONS The aim of the FPA series of Recommendations is to provide loss prevention guidance for industrial and commercial premises and systems. The series continues
PRC-SAF-22. Zachary Site. SAFETY POLICIES and PROCEDURES. Hot Work Permit. Revision #3-06/03/2011. Date Reason For Change Changed/Reviewed By
ZACHARY SITE PROCEDURE NUMBER TITLE: PRC-SAF-22 (Hot Work Permit) Page 1 of 20 Rev. 1.7 Date: 06/01/15 PRC-SAF-22 Zachary Site SAFETY POLICIES and PROCEDURES Revision #3-06/03/2011 Hot Work Permit Date
Safe Code of Practice. No.05 Hot Works Procedure
Safe Code of Practice No.05 Hot Works Procedure Version: 1.0 Date: 28 TH June 2016 Date: 28/0616 Review Date: 28/06/19 Issue No: 6 Page 1 of 7 INTRODUCTION The aim of this Safe Code of Practice is to give
Pocket Guide to Hot Work Loss Prevention. Sixth Edition
Pocket Guide to Hot Work Loss Prevention Sixth Edition Pocket Guide to Hot Work Loss Prevention Sixth Edition 4 Audience This pocket guide is intended for those involved with hot work management at client
HOT WORK PROCEDURE. A Page 1 of 20
TABLE OF CONTENTS 1. OBJECTIVE...4 2. SCOPE...4 3. DEFINITIONS...4 4. RESPONSIBILITIES...5 5. HAZARD AND RISK ASSESSMENT...5 5.1 PPA Controlled Hot Work Requirements Flow Chart...5 6. HOT WORK PERMIT...6
Supersedes: 2/16 (Rev.10) Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager
Procedure No.: PA-020-0002 Page: 1 of 29 Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager Document Revision Change Table Revision Number Revision Description Revised By Revision Date
HOT WORK 1. PURPOSE 2. SCOPE 3. KEY TERMS
Doc owner: Authorised by: HR Manager WHS Group Executive Human Resources HOT WORK Version PRO-05-11-01 Issue date 08/2017 1. PURPOSE The purpose of this procedure is to provide guidance to David Jones
Permit to Work Procedure
1. Purpose The permit to work procedure provides a system for managing certain high risk activities at NT Airports sites. The purpose of this procedure is to: 2. Scope Provide a level of control to ensure
MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY. To provide instruction for the issue and control of permits authorizing Hot Work operations.
DAIMLERCHRYSLER MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY Subject: HOT WORK PERMITS ISSUE AND CONTROL OF ISSUE DATE: 6/1/99 EFFECTIVE DATE: 6/1/99 REVIEW DATE. TBD SERIES & NO. SMI - 117 I. PURPOSE
PURPOSE To specify the minimum requirements for controlling risks associated with Hot Work activities.
PURPOSE To specify the minimum requirements for controlling risks associated with Hot Work activities. 1 SCOPE This procedure defines Hot Work as any activity that may introduce a source of ignition or
CHAPTER 1 GENERAL. 1
MINISTERIAL REGULATION ON THE PRESCRIBING OF STANDARD FOR ADMINISTRATION AND MANAGEMENT OF OCCUPATIONAL SAFETY, HEALTH AND WORK ENVIRONMENT IN CONFINED SPACE B.E. 2547 -------------------------------------
Luke Fania, Environment Team Leader David Donehue, Manager/Corporate Environment Megan Calvert, HSE Systems Manager
Controlled Document Hot Work and Fire Risk Work Summary The purpose of this procedure is to identify and control the risks associated with Hot Work and Fire Risk Work conducted by TransGrid employees and
Permit to Work System Training for Supervisors Managing Hot Works & Other Permits - Presenter s Guide
Permit to Work System Training for Supervisors Managing Hot Works & Other Permits - Presenter s Guide TABLE OF CONTENTS 1.0 PURPOSE... 3 2.0 SCOPE... 3 3.0 RELATED DOCUMENTS... 3 4.0 TRAINING DELIVERY...
Hot Work. A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use. Full Review of Document
A printed or saved copy is an UNCONTROLLED copy. Check that it is the latest available version before use. Title: Number: HOT WORK GM-11-036-06 Version Number: 10.0 Date Revised: 11 June 2015 Owner: Authoriser:
Permit to Work Systems
Permit to Work Systems Guidance Note 12 Jul 16 1 Permits to work systems Introduction This Guidance Note gives practical information about permit to work systems. A sample template has been included in
Classification: Public Rev. 00 June 2018 Page 1 of 25
Classification: Public Rev. 00 June 2018 Page 1 of 25 Rev. 00 June 2018 Page 2 of 25 Rev. 00 June 2018 Page 3 of 25 Rev. 00 June 2018 Page 4 of 25 Rev. 00 June 2018 Page 5 of 25 Rev. 00 June 2018 Page
Dangers of Hot Work: Key Lessons from CSB Investigations
2017 NFPA Conference & Expo Dangers of Hot Work: Key Lessons from CSB Investigations Presented by: Samuel A. Oyewole, PhD. Office of Investigations U.S. Chemical Safety Board Washington, DC 1 Disclaimer
VIRU KEEMIA GRUPP AS. Hot Works Safety Management Instruction No. 136
VKGj.TTO/39 VIRU KEEMIA GRUPP AS KINNITAN (allkirjastatud digitaalselt) Priit Rohumaa Juhatuse esimees veebruar 2013 (allkirjastatud digitaalselt) Meelis Eldermann Juhatuse liige veebruar 2013 Hot Works
PRO Hot Work
MS&L Procedure PRO-4.5-0001-1-07 Hot Work Version: 3 Authorised by: Tom Angliss & Owen Quake Authorisation Date: 21/11/2017 This document has been approved for release and changed as per the associated
Record of Revisions. SVP & General Manager, Freeport. Date Revision No. Details of Change
Site Function: Environmental, Health & Standard No.: BCF020.023 Page: Page 1 of 20 Site Representative Manager, Environ., Health & Record of Revisions Date Revision No. Details of Change 05/15/2018 9 4.5.3
PRO Hot Work
MS&L Procedure PRO-4.5-0001-1-07 Hot Work Document Owner: Bill Kruesi HSSE Manager - Asset Mgmt. Owen Quake ANZ Engineering Authority Approved By: Bill Kruesi HSSE Manager - Asset Mgmt. Control of Work
Fullerton, CA Municipal Code. Chapter FULLERTON FIRE CODE
Fullerton, CA Municipal Code Chapter 13.20. 2013 FULLERTON FIRE CODE Sections: 13.20.010 Adoption of the 2013 California Fire Code. 13.20.020 Title. 13.20.030 Applicability. 13.20.040 Department of Fire
TOWN OF WINDSOR BYLAW # 18 PREVENTION OF FIRE BYLAW
TOWN OF WINDSOR BYLAW # 18 PREVENTION OF FIRE BYLAW 18.01 No person being in any building or structure on which or in which notices have been posted by order of a fire marshal to forbid smoking therein
MINIMUM HOUSING STANDARDS ORDINANCE
MINIMUM HOUSING STANDARDS ORDINANCE FINDINGS AND AUTHORITY. Pursuant to G. S. 160-A-441, it is hereby declared that there exist in the planning jurisdiction of the Town of Pine Level, dwellings which are
THE CORPORATION OF THE CITY OF GUELPH THE COUNCIL OF THE CORPORATION OF THE CITY OF GUELPH. 1. This By-law may be cited as the Fire Prevention By-law.
THE CORPORATION OF THE CITY OF GUELPH By-law Number (1988)-12716 Office Consolidation Being a by-law to adopt the National Fire Code of Canada, 1985, and to make such other regulations as are deemed necessary
Coles Express Work Clearance: Induction for Contractors
Coles Express Work Clearance: Induction for Contractors Part of the Coles Online Contractor Induction system, for completion by contractors who will conduct works on Coles Express sites. Prerequisites
A BYLAW RESPECTING OPEN FIRES AND FIREWORKS
THE LAST MOUNTAIN REGIONAL PARK AUTHORITY, IN THE PROVINCE OF SASKATCHEWAN ENACTS AS FOLLOWS: Short Title This bylaw shall be cited as the Open Fire and Fireworks Bylaw. Purpose The purpose of this Bylaw
HEALTH & SAFETY HOT WORK INSTRUCTIONS
HEALTH & SAFETY HOT WORK INSTRUCTIONS 1. RISK ASSESSMENT 1.1 Requirements The hot work authoring officer (HW authorising officer), in conjunction with the employee/contractor conducting the hot work activity
BY-LAW NUMBER.: OF THE CITY OF SARNIA-CLEARWATER. "A By-Law to provide for the Licensing and Regulation of Public Halls"
BY-LAW NUMBER.:2 7 1991 OF THE CITY OF SARNIA-CLEARWATER "A By-Law to provide for the Licensing and Regulation of Public Halls" WHEREAS The Public Halls Act provides that no public hall shall be offered
REGULATIONS OF THE BOARD OF HEALTH OF THE LAKE COUNTY GENERAL HEALTH DISTRICT PART SIXTEEN - DWELLING UNITS CODE. Chapter Housing.
REGULATIONS OF THE BOARD OF HEALTH OF THE LAKE COUNTY GENERAL HEALTH DISTRICT PART SIXTEEN - DWELLING UNITS CODE Chapter 1610. Housing. CHAPTER 1610 Housing 1610.01 Definitions. 1610.05 Violations; notices
GARFIELD COUNTY ORDINANCE NO.
GARFIELD COUNTY ORDINANCE NO. ORDINANCE AMENDING ORDINANCE 2005-1 AND 2006-1 RELATING TO THE ADOPTION OF THE 2015 INTERNATIONAL FIRE CODE, AND THE ADOPTION OF THE 2015 INTERNATIONAL FIRE CODE WHEREAS,
BE IT ORDAINED BY THE COUNCIL OF THE CITY OF TOPEKA, KANSAS: Section 1. That section , Uniform Mechanical Code Adopted, of The
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 (Published in the Topeka Metro News February 11, 2009) ORDINANCE NO. 19216 AN ORDINANCE introduced by City Manager Norton N. Bonaparte, Jr., amending
A LOCAL LAW PROVIDING FOR THE ADMINISTRATION AND ENFORCEMENT OF THE NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE
A LOCAL LAW PROVIDING FOR THE ADMINISTRATION AND ENFORCEMENT OF THE NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE Local Law #2 of 2007. Be it enacted by the Town Board of the Town of Oswego,