MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY. To provide instruction for the issue and control of permits authorizing Hot Work operations.

Size: px
Start display at page:

Download "MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY. To provide instruction for the issue and control of permits authorizing Hot Work operations."

Transcription

1 DAIMLERCHRYSLER MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY Subject: HOT WORK PERMITS ISSUE AND CONTROL OF ISSUE DATE: 6/1/99 EFFECTIVE DATE: 6/1/99 REVIEW DATE. TBD SERIES & NO. SMI I. PURPOSE To provide instruction for the issue and control of permits authorizing Hot Work operations. II. REFERENCES Federal and State Occupational Health & Safety Acts Plant Security Operations Fire Prevention Book of Knowledge Requirements Section 4.24 Cutting and Welding III. FUNCTIONS AFFECTED Advance Manufacturing Engineering Plant Facility Engineering Maintenance Employee Safety Plant Security Operations IV. OPERATIONS AFFECTED All DaimlerChrysler Operations V. DEFINITIONS Fire Watch. A person designated to observe conditions in the immediate area of a Hot Work operation commencing with the start of the Hot Work operation and concluding 30 minutes after the Hot Work operation has been completed. Standby. A qualified person designated to observe conditions in the immediate area of a Hot Work operation judged to contain hazardous conditions that cannot be eliminated. That person shall be present at the site commencing with the start of the Hot Work operation, and concluding 30 minutes after the Hot Work operation has been completed. Hot Work. All non-production related work that creates sparks or generates hot byproducts that are capable of SMI-117, Page 1 of 5

2 igniting a fire in the surrounding area of the work site. Examples of such operations include, but are not limited to: grinding, cutting, welding, torch soldering, etc. Workmen. DaimlerChrysler employees from performing group, or those contracted by DaimlerChrysler. Hot Work Permit. DaimlerChrysler form No , Rev.4/99 Performing Group. DaimlerChrysler employee department(s) performing the Hot Work operation. Breakdown Emergency. An unscheduled event that interrupts, or threatens to interrupt production operations. Qualified Person. A person trained or instructed in fire prevention principles as outlined in the Supplemental Response Team, in the Fire Emergency Response Organization booklet. (Form No , Rev. 5/90.) VI. INSTRUCTIONS A. Use of the Permit 1. A Hot Work Permit (Exhibit A) is used to authorize DaimlerChrysler employees or outside contractors to perform Hot Work operations. A Hot Work Permit is not issued for DaimlerChrysler employees for jobs performed in a location designated for Hot Work operations and previously approved by Plant Security Operations for that purpose. 2. Hot Work operations conducted in response to a Breakdown Emergency may be initiated before the issue of a Hot Work Permit provided all the required precautions listed on the Hot Work Permit have been taken. A Hot Work Permit shall be obtained as soon as possible in such circumstances. 3. A Hot Work Permit shall be issued for all contractors assigned Hot Work Operations inside or within 50 of an operating DaimlerChrysler facility. B. Issuing Permits 1. The Hot Work Permit shall be prepared and sign by: a. The supervisor of the performing department. b. Facility Engineering when the work is performed by outside contractors. c. Facility Engineering shall be responsible for briefing contractors regarding the details of this instruction. 2. The Hot Work Permit is approved and authorized by: Plant Security Operations, or a qualified person where Plant Security Operation personnel are not on site. The Hot Work Permit shall be signed only after inspecting the work area to ensure the requirements and safety precautions listed on the permit have been provided. 3. The Hot Work Permit is valid: a. For the work shift or day specified on the face of the permit. A new permit must be issued for each subsequent work shift or day of operation. b. For the area specified on the face of the permit. A new permit must be issued if the operation is conducted in a location other than that listed on the face of the permit. c. For the job specified on the face of the permit. A new permit must be issued if the nature of the work is other than that listed on the face of the permit. SMI-117, Page 2 of 5

3 4. Hot Work Permit Display The hard copy of the Hot Work Permit shall be visibly displayed at the site of the Hot Work for the duration of the operation. 5. Hot Work Permit form retention The soft white copy of the Hot Work Permit shall be retained on file for a period of (1) year from the date issued by Plant Security Operations or where Plant Security Operations is not on site, by the department approving and authorizing the permit. C. Control of Hazardous Conditions 1. The supervisor of the department performing the Hot Work has the primary responsibility for the safety performance of the Hot Work operation. 2. Plant Security Operations, or other qualified person(s) where Plant Security Operations is not on site, is responsible for assuring that hazardous conditions are corrected by the responsible supervision before approving and authorizing the Hot Work Operation to begin. VII. EXHIBIT A. Exhibit A Hot Work Permit, Form No , Rev. 4/99. SMI-117, Page 3 of 5

4 EXHIBIT A, Side 1 SMI-117, Page 4 of 5

5 EXHIBIT A, Side 2 SMI-117, Page 5 of 5

RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM

RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM REV 12/99 1 TABLE OF CONTENTS HOT WORK PERMIT PROGRAM A. Purpose and Scope.3 B. Hot Work Permit Procedures...3 C. Hot Work Permit - Prohibited Conditions...4

More information

RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM

RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM RUTGERS UNIVERSITY HOT WORK PERMIT PROGRAM REV 10/2015 TABLE OF CONTENTS HOT WORK PERMIT PROGRAM Contents A. PURPOSE AND SCOPE... 3 B. HOT WORK PERMIT PROCEDURES... 3 C. HOT WORK PERMIT PROHIBITED CONDITIONS:...

More information

Roger Williams University Hot Work Plan

Roger Williams University Hot Work Plan Roger Williams University Hot Work Plan Roger Williams University Dept. Of Environmental Health and Safety One Old Ferry Road Bristol, RI 02809 Adopted: April 26, 2011(President s Cabinet) Roger Williams

More information

Desert Research Institute Hot Work Permit Program

Desert Research Institute Hot Work Permit Program 1.0 INTRODUCTION 1.1 PURPOSE The purpose of this policy is to prevent any fires that may result from hot work processes. 1.2 SCOPE 1.2.1 For the purposes of this policy, hot work is defined as any temporary

More information

University of Delaware.

University of Delaware. HOT WORK PERMIT PROGRAM The following information describes the code required Hot Work Permit Program at the University of Delaware. PART 1 GENERAL University Contact: Department of Environmental Health

More information

University of Central Missouri Hot Work Permit Program

University of Central Missouri Hot Work Permit Program 1. Introduction University of Central Missouri Hot Work Permit Program The University of Central Missouri's (UCM) Hot Work Program is designed to minimize risks to our campus community, which includes

More information

Risk Control Guide HOT WORK

Risk Control Guide HOT WORK HOT WORK RCG003 (E)-v2-01/2017 Page 1 2017 Royal & Sun Alliance Insurance plc Introduction Hot work is defined as any operation that involves open flames or produces heat or sparks, e.g. cutting, grinding,

More information

(WELDING, CUTTING, AND OPEN FLAME WORK)

(WELDING, CUTTING, AND OPEN FLAME WORK) THE UNIVERSITY OF TEXAS AT TYLER Hot Work (WELDING, CUTTING, AND OPEN FLAME WORK) Program 2016 Table of Contents 1. INTRODUCTION... 3 2. PURPOSE... 3 3. APPLICATION... 3 4. DEFINITIONS... 3 5. PROGRAM

More information

HOT WORK PERMIT PROGRAM REVISED AND DISTRIBUTED BY: THE UNIVERSITY OF VERMONT DEPARTMENT OF PHYSICAL PLANT TRAINING & COMPLIANCE OFFICE

HOT WORK PERMIT PROGRAM REVISED AND DISTRIBUTED BY: THE UNIVERSITY OF VERMONT DEPARTMENT OF PHYSICAL PLANT TRAINING & COMPLIANCE OFFICE University of Vermont Department of Physical Plant Burlington, Vermont HOT WORK PERMIT PROGRAM REVISED AND DISTRIBUTED BY: THE UNIVERSITY OF VERMONT DEPARTMENT OF PHYSICAL PLANT TRAINING & COMPLIANCE OFFICE

More information

Villanova University Department of Environmental Health and Safety Policy and Procedure Manual

Villanova University Department of Environmental Health and Safety Policy and Procedure Manual Villanova University Department of Environmental Health and Safety Policy and Procedure Manual Subject: Hot Works Procedure Number: S15 Effective: 20 Apr 99 Revised: 9-15-15 I Purpose: To establish a procedure

More information

STANDARD PROCEDURE INSTRUCTION

STANDARD PROCEDURE INSTRUCTION STANDARD PROCEDURE INSTRUCTION Title SPI Department Hot Work Permit Supersedes SPI Dated # 34-3 Effective Date Safety, Health and Environment Dec 22, 2014 Jan 19, 2016 Hot Work Permit 1. PURPOSE 1.1 To

More information

Hot Work Procedures. Competent means possessing knowledge, experience and training to perform a specific duty.

Hot Work Procedures. Competent means possessing knowledge, experience and training to perform a specific duty. Hot Work Procedures Purpose This procedure will provide the knowledge and equipment required to minimize the identified workplace hazards associated with Hot Work. These procedures will provide: information

More information

SUNY Geneseo ENVIRONMENTAL HEALTH & SAFETY

SUNY Geneseo ENVIRONMENTAL HEALTH & SAFETY Revision No.: 1 Page 1 of 7 I. PURPOSE The purpose of this policy is to establish minimum standards for safely conducting hot work tasks to help mitigate hazards that could occur during hot work operations.

More information

SAFETY AND HEALTH STANDARD HOT WORK PERMIT Effective Date: 06/10/10 Standard: 16.1 Document Number: KUCSH0040 Rev: 04

SAFETY AND HEALTH STANDARD HOT WORK PERMIT Effective Date: 06/10/10 Standard: 16.1 Document Number: KUCSH0040 Rev: 04 16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to prevent the inadvertent ignition of combustible materials when performing hot work. 16.1.2 DEFINITIONS 16.1.2.1 Hot work - includes welding,

More information

Hot Work Program. SUNY Canton. Purpose

Hot Work Program. SUNY Canton. Purpose SUNY Canton Hot Work Program Purpose Hot Work is defined as welding, thermite welding, thermal spraying, installation of torch applied roof systems, cutting, soldering, brazing, grinding, thawing pipe

More information

Environmental, Health and Safety. UNC Charlotte Hot Work Program (Welding, Cutting, and Brazing)

Environmental, Health and Safety. UNC Charlotte Hot Work Program (Welding, Cutting, and Brazing) Environmental, Health and Safety UNC Charlotte Hot Work Program (Welding, Cutting, and Brazing) January 2014 TABLE OF CONTENTS PURPOSE:... 2 SCOPE:... 2 HOT WORK RESPONSIBILITIES... 2 SPECIFIC DEPARTMENTAL

More information

OFFICE OF STATE HUMAN RESOURCES

OFFICE OF STATE HUMAN RESOURCES OFFICE OF STATE HUMAN RESOURCES NUMBER: HWP-1 TOTAL PAGES: 6 SUBJECT: Hot Work Program Effective Date: Revision Date: Revision #: RELATED LEGISLATION: This program outlines procedures for [Agency/University]

More information

"HOT WORK SAFETY AND THE PERMITTING PROCESS"

HOT WORK SAFETY AND THE PERMITTING PROCESS PRESENTER'S GUIDE "HOT WORK SAFETY AND THE PERMITTING PROCESS" Part of the "SAFETY MEETING KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE

More information

Prevention of Hot Work Fires in Healthcare Facilities. Sherie Van Slyke Engineering Specialist

Prevention of Hot Work Fires in Healthcare Facilities. Sherie Van Slyke Engineering Specialist Prevention of Hot Work Fires in Healthcare Facilities Sherie Van Slyke Engineering Specialist Are hot work fires common in hospitals? What is hot work? Hot work statistics The contractor component. Construction

More information

Hot Work Program. Program Origination: October, 2017

Hot Work Program. Program Origination: October, 2017 Hot Work Program Program Origination: October, 2017 Contact Personnel: Jason Kayser, Fire & Safety Specialist Jason.kayser@uni.edu 319-273-2004 Hot Work Program UNI Employees & Contractors October, 2017

More information

Hot Work Safety and the Permitting Process. Leaders Guide and Quiz

Hot Work Safety and the Permitting Process. Leaders Guide and Quiz ! Hot Work Safety and the Permitting Process Leaders Guide and Quiz 4879 INTRODUCTION TO THE PROGRAM Structure and Organization Information in this program is presented in a definite order so that employees

More information

Making sense of risk Risk engineering. Marine hot work Permit to Work (PTW) systems

Making sense of risk Risk engineering. Marine hot work Permit to Work (PTW) systems Marine hot work Permit to Work (PTW) systems Marine hot work Permit to Work (PTW) systems Hot work is any operation involving open flames or producing heat and/or sparks, including but not limited to welding,

More information

Hot Work Permit Guidelines

Hot Work Permit Guidelines 2408 Wanda Daley Drive Ames, Iowa 50011-3602 (515) 294-5359 www.ehs.iastate.edu Copyright 2014 Reviewed 2015 2 Hot Work Permit Guidelines Directory of Service and Emergency Providers Services Environmental

More information

Hot Work Policy & Procedure

Hot Work Policy & Procedure Hot Work Policy & Procedure Policy: Reference: The purpose of the PCS General Contractor Hot Work policy is to protect personnel and property from a fire caused by hot work. The PCS Hot Work procedure

More information

Areas that have been designed and constructed for performing open-flame or spark-producing work.

Areas that have been designed and constructed for performing open-flame or spark-producing work. PURPOSE Baylor University recognizes that there is a potential for injury to people and damage to property that can result from fire or sparks that arise when hot work is performed outside of a designated

More information

KENNECOTT UTAH COPPER

KENNECOTT UTAH COPPER 16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to define the requirement for performing hot work operations on certain components of machinery, equipment and structures and preventing the

More information

HOT WORK SAFETY GUIDELINE

HOT WORK SAFETY GUIDELINE HOT WORK SAFETY GUIDELINE SAFETY GUIDELINE 2017 1 Hot work safety guideline Index 1 Hot work training... 2 2 Purpose of the safety guidelines... 2 3 Binding force of the safety guidelines... 2 4 Definitions...

More information

HOT WORK PROGRAM OSHA

HOT WORK PROGRAM OSHA HOT WORK PROGRAM 1910.252 OSHA Table of Contents Purpose... 3 Definitions... 3 Responsibilities... 3 Hot Work Permitted Locations... 5 Fire Prevention Precautions... 5 Personal Protective Equipment...

More information

Hot Work Procedure. Work Health and Safety Policy Responsible Officer. Executive Director, Infrastructure Services and Development Approved by

Hot Work Procedure. Work Health and Safety Policy Responsible Officer. Executive Director, Infrastructure Services and Development Approved by Hot Work Procedure Related Policy Work Health and Safety Policy Responsible Officer Executive Director, Infrastructure Services and Development Approved by Executive Director, Infrastructure Services and

More information

Hot Work Permit Program

Hot Work Permit Program Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0 Training.. 5 5.0 Recordkeeping. 5 6.0 Permits

More information

Hot Work Permit Program

Hot Work Permit Program Environmental Health and Safety Office Hot Work Permit Program Permitting Process for welding, cutting and brazing. Adopted: March 6, 2007 Revised: 7/18/16 http://www.stlawu.edu/environmentalhealth-and-safety/environmental-healthand-safety-policies

More information

PURPOSE:... 3 EMPLOYEE CLASSIFICATIONS:... 3 OUTSIDE PERSONNEL (I.E., CONTRACTORS):... 4 HOT WORK REQUIREMENTS:... 4 EMPLOYEE TRAINING:...

PURPOSE:... 3 EMPLOYEE CLASSIFICATIONS:... 3 OUTSIDE PERSONNEL (I.E., CONTRACTORS):... 4 HOT WORK REQUIREMENTS:... 4 EMPLOYEE TRAINING:... South Central College North Mankato/Mankato Campus 1920 Lee Boulevard N. Mankato, MN 56002-1920 Faribault Campus 1225 Third Street SW Faribault, MN 55021-5782 Adoption Date: 09-18-15 Revision Date: 02-23-17

More information

PRO Hot Work

PRO Hot Work MS&L Procedure PRO-4.5-0001-1-07 Hot Work Version: 3 Authorised by: Tom Angliss & Owen Quake Authorisation Date: 21/11/2017 This document has been approved for release and changed as per the associated

More information

Hot Work Permitting Procedure

Hot Work Permitting Procedure Hot Work Permitting Procedure Purpose Audience Policy This procedure is designed to ensure that spark and flame producing construction and maintenance activities do not present an undue fire hazard to

More information

Hot Work Program June 2017

Hot Work Program June 2017 Hot Work Program June 2017 Hot Work Program TABLE of CONTENTS I. General Information II. Definitions III. Roles and Responsibilities IV. Hot Work Areas V. Hot Work Permit VI. Hot Work Permit-Not Required

More information

HOT WORK 1. PURPOSE 2. SCOPE 3. KEY TERMS

HOT WORK 1. PURPOSE 2. SCOPE 3. KEY TERMS Doc owner: Authorised by: HR Manager WHS Group Executive Human Resources HOT WORK Version PRO-05-11-01 Issue date 08/2017 1. PURPOSE The purpose of this procedure is to provide guidance to David Jones

More information

Fire caused by Hot Works. A guide to loss prevention

Fire caused by Hot Works. A guide to loss prevention Fire caused by Hot Works A guide to loss prevention Hot Work is usually defined as any open flame, spark or heat producing activity and is typically associated with cutting, welding, grinding and brazing

More information

PRO Hot Work

PRO Hot Work MS&L Procedure PRO-4.5-0001-1-07 Hot Work Document Owner: Bill Kruesi HSSE Manager - Asset Mgmt. Owen Quake ANZ Engineering Authority Approved By: Bill Kruesi HSSE Manager - Asset Mgmt. Control of Work

More information

HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY RISK MANAGEMENT & SAFETY

HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY RISK MANAGEMENT & SAFETY HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY RISK MANAGEMENT & SAFETY WHAT IS HOT WORK? WORK INVOLVING BURNING, WELDING, OR A SIMILAR OPERATION THAT IS CAPABLE OF INITIATING FIRES OR EXPLOSIONS. EXAMPLES

More information

RISKTOPICS. DISCUSSION For the purposes of this document, hot work: Management practices: Hot work Property and Business Interruption January 2013

RISKTOPICS. DISCUSSION For the purposes of this document, hot work: Management practices: Hot work Property and Business Interruption January 2013 RISKTOPICS Management practices: Hot work Property and Business Interruption January 2013 This document highlights the property conservation responsibilities of those who utilize hot work outside of areas

More information

HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY SAFETY AND HEALTH RISK MANAGEMENT AND SAFETY

HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY SAFETY AND HEALTH RISK MANAGEMENT AND SAFETY HOT WORK PERMIT PROGRAM AUBURN UNIVERSITY SAFETY AND HEALTH RISK MANAGEMENT AND SAFETY WORK INVOLVING BURNING, WELDING, OR A SIMILAR OPERATION THAT IS CAPABLE OF INITIATING FIRES OR EXPLOSIONS. WHAT IS

More information

TAMPA ELECTRIC COMPANY ENERGY SUPPLY HOT WORK PERMITTING PROGRAM

TAMPA ELECTRIC COMPANY ENERGY SUPPLY HOT WORK PERMITTING PROGRAM TABLE OF CONTENTS TITLE PAGE # PURPOSE / INTRODUCTION 1 RESPONSIBILITY 2 EMPLOYEE TRAINING AND DOCUMENTATION 3 PROGRAM REQUIREMENTS 4 HOT WORK PERMIT PLANNING AND PRECAUTIONS 4 6 FIREWATCH 6, 7 HOT WORK

More information

Hot Work Permitting Program

Hot Work Permitting Program Hot Work Permitting Program Environmental Health, Safety, and Risk Management Department Box 6113, SFA Station Nacogdoches, Texas 75962-6113 Original: January 2004 Revised: January 2011, April 2018 Table

More information

Hot Work Program. Purpose of Procedure:

Hot Work Program. Purpose of Procedure: BGSU Hot Work Program Page 1 Bowling Green State University Purpose of Procedure: Hot Work Program These procedures have been established to comply with Ohio s Public Employee Risk Reduction Act, the OSHA

More information

IWU PHYSICAL PLANT SAFETY PROGRAM

IWU PHYSICAL PLANT SAFETY PROGRAM STANDARDS Welding, Cutting and Brazing/General Requirements OSHA 1910.252, 1. Purpose Hot work is any temporary or permanent operation involving open flames or producing heat and/or sparks. This includes

More information

The Ohio State University. Hot Work Permit Program (Welding, Cutting and Brazing)

The Ohio State University. Hot Work Permit Program (Welding, Cutting and Brazing) Environmental Health & Safety 1314 Kinnear Rd. Columbus, Ohio 43212 Phone (614) 292-1284 Fax (614) 292-6404 http://www.ehs.osu.edu/ The Ohio State University Hot Work Permit Program (Welding, Cutting and

More information

Non Electrical Hot Work Program

Non Electrical Hot Work Program Environmental Health and Safety Name: Non Electrical Hot Work Program Date Created: 02/18/2014 Date Revised: Created By: Bob Happel PURPOSE The purpose of this Program is to protect people and property

More information

Hot Work and Welding Management Procedures Attached to FIN-INS Introduction. 1.1 Purpose

Hot Work and Welding Management Procedures Attached to FIN-INS Introduction. 1.1 Purpose 1. Introduction 1.1 Purpose Hot Work and Welding Management Procedures Attached to FIN-INS-22 Indiana University Insurance, Loss Control and Claims (INLOCC) and Indiana University Environmental Health

More information

HOT WORK GUIDELINES 3. MANDATORY AREAS REQUIRING HOT WORK PERMITS Within the Service Station Site

HOT WORK GUIDELINES 3. MANDATORY AREAS REQUIRING HOT WORK PERMITS Within the Service Station Site 1. GENERAL This procedure gives guidelines for the precautions and preparation that should be followed to ensure that work covered by a hot work permit can be carried out safely without risk to people

More information

University Environmental Health and Safety. Hot Work Permit Program

University Environmental Health and Safety. Hot Work Permit Program University Environmental Health and Safety Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0

More information

General Hot Work Program Guidelines. Lyndsey Beaudin

General Hot Work Program Guidelines. Lyndsey Beaudin General Hot Work Program Guidelines Lyndsey Beaudin WHY SUCH A HOT TOPIC? NEW YORK STATE OFFICE OF FIRE PROTECTION AND CONTROL Violation: Hot Work Permit not issued for Hot Work Area 2603.4 Hot Work Program

More information

University of Nevada, Reno

University of Nevada, Reno University of Nevada, Reno HOT WORK PERMIT PROGRAM Program Contact Person: John A. Braun, CSP Environmental Health and Safety University of Nevada, Reno Phone: 775-784-6478 HOT WORK PERMIT PROGRAM UNIVERSITY

More information

Using the WPTW System: Frequently Asked Questions

Using the WPTW System: Frequently Asked Questions Using the WPTW System: Frequently Asked Questions The Wellsite Permit to Work (WPTW) System is a robust and comprehensive approach to the planning and authorisation of work activities on onshore wellsites.

More information

MCW s Hot Work Permit Program

MCW s Hot Work Permit Program 2019 MCW s Hot Work Permit Program - Hot Work/Fire Watch Operations This document is the Medical College of Wisconsin s (MCW) written program for conducting hot work, and identifies roles and responsibilities

More information

Guide to Hot Work NFPA 51B Understanding the new requirements after July 1, 2018

Guide to Hot Work NFPA 51B Understanding the new requirements after July 1, 2018 Guide to Hot Work NFPA 51B Understanding the new requirements after July 1, 2018 What is the issue that caused the change? Unpermitted hot work was determined to be the cause of a fire that killed two

More information

Permit to Work Procedure

Permit to Work Procedure 1. Purpose The permit to work procedure provides a system for managing certain high risk activities at NT Airports sites. The purpose of this procedure is to: 2. Scope Provide a level of control to ensure

More information

KENNECOTT UTAH COPPER

KENNECOTT UTAH COPPER 16.1.1 INTRODUCTION 16.1.1.1 The purpose of this standard is to define the requirement for performing hot work operations on certain components of machinery, equipment and structures and preventing the

More information

Hot Work Program. Roles and Responsibilities. Management. PAI Responsibilities

Hot Work Program. Roles and Responsibilities. Management. PAI Responsibilities Hot Work Program Scope is aware of the hazards associated with hot work operations (cutting, welding, brazing and soldering, grinding, etc.) is committed to keeping our employees safe and to control hazards

More information

This program applies to University faculty, staff, students, vendors, or contractors performing Hot Work on behalf of the University of Iowa.

This program applies to University faculty, staff, students, vendors, or contractors performing Hot Work on behalf of the University of Iowa. University of Iowa Hot Work Loss Prevention Program This program has been approved for use at the University of Iowa and will remain in effect until a revised program is developed and approved. Written:

More information

Fire safety basics for hot work operatives. CFPA-E Guideline No 12:2012 F

Fire safety basics for hot work operatives. CFPA-E Guideline No 12:2012 F Fire safety basics for hot work operatives CFPA-E Guideline No 12:2012 F FOREWORD The European fire protection associations have decided to produce common guidelines in order to achieve similar interpretation

More information

HOT WORK MANAGEMENT PROGRAM

HOT WORK MANAGEMENT PROGRAM HOT WORK MANAGEMENT PROGRAM Rose-Hulman Institute of Technology Table of Contents SECTION 1.0 Purpose 2.0 Regulatory Reference 3.0 Scope 4.0 Elements of the Program 5.0 Responsibility 6.0 Training and

More information

Hot Work. Approved by: Ruth Hampton Review Date: 6 th December 2015

Hot Work. Approved by: Ruth Hampton Review Date: 6 th December 2015 5 WHS PROCEDURE P28-01 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment for all persons

More information

HOT WORK SAFETY GUIDE. Specific responsibilities relating to hot work operations are outlined below.

HOT WORK SAFETY GUIDE. Specific responsibilities relating to hot work operations are outlined below. HOT WORK SAFETY GUIDE Version Date Comments 5 March, 2012 Revised document 6 June, 2015 Update code citation - SFPC 2012 A. INTRODUCTION The purpose of this Guide is to provide information regarding welding

More information

Apply for Hot Works Permit

Apply for Hot Works Permit Apply for Hot Works Permit Details of revisions Level Details Date Initial 1 Creation of initial document for use 20/08/2016 J.O S 2 Review and Amendment 26/02/2018 MW Title: Apply for Hot Works Permit

More information

Fire Safety & Hot Work Permits. Oakland University Office of EH&S

Fire Safety & Hot Work Permits. Oakland University Office of EH&S Fire Safety & Hot Work Permits Oakland University Office of EH&S Topics of Discussion Why do we Need a Hot Work Permit Real-life Cutting/Welding Accidents When is a Hot Work Permit Required Hot Work Precautions

More information

Hot Work Safety Program

Hot Work Safety Program Hot Work Safety Program 6900-2.0 Associated OHS Process: General Industry & Construction Safety The master copy of this document resides in electronic format. Printed copies of this document are for convenience

More information

Process: Permit to Work PS-OP-RC-2011

Process: Permit to Work PS-OP-RC-2011 Contents 1.0 Objective... 2 2.0 3.0 Scope... 2 Implementation... 3 3.1. Permit Application... 4 3.1.1. Risk Assessment... 5 3.2. Permit Administration... 6 3.2.1. RMIT Internal Consultation... 7 3.3. Permit

More information

Hot Work Permit Program

Hot Work Permit Program Hot Work Permit Program 1 2 TABLE OF CONTENTS Section Title Page 1.0 Scope 3 2.0 Standards and Regulations Involved/Target Groups 3 3.0 Responsibilities 4 4.0 Training.. 5 5.0 Recordkeeping. 5 6.0 Permits

More information

Classification: Public Rev. 00 June 2018 Page 1 of 25

Classification: Public Rev. 00 June 2018 Page 1 of 25 Classification: Public Rev. 00 June 2018 Page 1 of 25 Rev. 00 June 2018 Page 2 of 25 Rev. 00 June 2018 Page 3 of 25 Rev. 00 June 2018 Page 4 of 25 Rev. 00 June 2018 Page 5 of 25 Rev. 00 June 2018 Page

More information

Safe Code of Practice. No.05 Hot Works Procedure

Safe Code of Practice. No.05 Hot Works Procedure Safe Code of Practice No.05 Hot Works Procedure Version: 1.0 Date: 28 TH June 2016 Date: 28/0616 Review Date: 28/06/19 Issue No: 6 Page 1 of 7 INTRODUCTION The aim of this Safe Code of Practice is to give

More information

Pocket Guide to Hot Work Loss Prevention. Sixth Edition

Pocket Guide to Hot Work Loss Prevention. Sixth Edition Pocket Guide to Hot Work Loss Prevention Sixth Edition Pocket Guide to Hot Work Loss Prevention Sixth Edition 4 Audience This pocket guide is intended for those involved with hot work management at client

More information

CITY OF KAMLOOPS BY-LAW NO (AS AMENDED)

CITY OF KAMLOOPS BY-LAW NO (AS AMENDED) This is a consolidated by -law prepared by the City of Kamloops for convenience only. The City does not w arrant that the information contained in this consolidation is current. It is the responsibility

More information

Permit to Work System Training for Supervisors Managing Hot Works & Other Permits - Presenter s Guide

Permit to Work System Training for Supervisors Managing Hot Works & Other Permits - Presenter s Guide Permit to Work System Training for Supervisors Managing Hot Works & Other Permits - Presenter s Guide TABLE OF CONTENTS 1.0 PURPOSE... 3 2.0 SCOPE... 3 3.0 RELATED DOCUMENTS... 3 4.0 TRAINING DELIVERY...

More information

Loss Prevention Standards

Loss Prevention Standards Introduction A hot work management system and associated permit is a formal recorded process used to help control work which is identified as potentially hazardous, and is an important part of an organisation

More information

HOT WORK PROCEDURE. A Page 1 of 20

HOT WORK PROCEDURE. A Page 1 of 20 TABLE OF CONTENTS 1. OBJECTIVE...4 2. SCOPE...4 3. DEFINITIONS...4 4. RESPONSIBILITIES...5 5. HAZARD AND RISK ASSESSMENT...5 5.1 PPA Controlled Hot Work Requirements Flow Chart...5 6. HOT WORK PERMIT...6

More information

Dangers of Hot Work: Key Lessons from CSB Investigations

Dangers of Hot Work: Key Lessons from CSB Investigations 2017 NFPA Conference & Expo Dangers of Hot Work: Key Lessons from CSB Investigations Presented by: Samuel A. Oyewole, PhD. Office of Investigations U.S. Chemical Safety Board Washington, DC 1 Disclaimer

More information

Minutes of Meeting, August 15, 2011

Minutes of Meeting, August 15, 2011 Minutes of Meeting, August 15, 2011 MINUTES of the SPOA BOARD MEETING August 15, 2011 Meeting was called to order by Jim Soden. Attendees The following persons where present for the meeting: Jim Soden

More information

Program Title Hot Work Program. Classification Fire Safety and Emergency Response. Program No INTRODUCTION

Program Title Hot Work Program. Classification Fire Safety and Emergency Response. Program No INTRODUCTION 1.0 INTRODUCTION ENVIRONMENTAL HEALTH AND SAFETY PROGRAM MANUAL As part of the Weill Cornell Medical College (WCMC) Environmental Health and Safety (EHS) Program Manual, this has been established. The

More information

HEALTH & SAFETY HOT WORK INSTRUCTIONS

HEALTH & SAFETY HOT WORK INSTRUCTIONS HEALTH & SAFETY HOT WORK INSTRUCTIONS 1. RISK ASSESSMENT 1.1 Requirements The hot work authoring officer (HW authorising officer), in conjunction with the employee/contractor conducting the hot work activity

More information

Permit to Work Systems

Permit to Work Systems Permit to Work Systems Guidance Note 12 Jul 16 1 Permits to work systems Introduction This Guidance Note gives practical information about permit to work systems. A sample template has been included in

More information

CONSERVATION AND DEVELOPMENT PARKS AND RESERVATIONS. Title 13 Chapter 9 State Forest Fire Service

CONSERVATION AND DEVELOPMENT PARKS AND RESERVATIONS. Title 13 Chapter 9 State Forest Fire Service CONSERVATION AND DEVELOPMENT PARKS AND RESERVATIONS Title 13 Chapter 9 State Forest Fire Service 13:9-1. Forest fire service established The Department of Environmental Protection shall maintain a forest

More information

DUQUESNE UNIVERSITY HOT WORK PROGRAM

DUQUESNE UNIVERSITY HOT WORK PROGRAM DUQUESNE UNIVERSITY HOT WORK PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Responsibilities 2 General Requirements 2 Welding or Cutting Containers

More information

HOT WORK PROGRAM October 2016

HOT WORK PROGRAM October 2016 HOT WORK PROGRAM October 2016 A. SCOPE AND APPLICATION The UNLV Hot Work Program is established in accordance with the standards listed in Section H and specifies the requirements and procedures necessary

More information

4.1 PERMIT TO WORK PROCEDURE

4.1 PERMIT TO WORK PROCEDURE TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 Purpose... 1 1.2 SCOPE... 2 2. ROLES AND RESPONSIBILITIES... 2 2.1 Permit Authoriser... 2 2.2 Permit Applicant... 3 2.3 HSEQ Manager... 3 2.4 Approvers... 3 2.5

More information

C174 Prevention of Major Industrial Accidents Convention, 1993

C174 Prevention of Major Industrial Accidents Convention, 1993 Page 1 of 9 C174 Prevention of Major Industrial Accidents Convention, 1993 Convention concerning the Prevention of Major Industrial Accidents (Note: Date of coming into force: 03:01:1997.) Convention:C174

More information

A LOCAL LAW PROVIDING FOR THE ADMINISTRATION AND ENFORCEMENT OF THE NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE

A LOCAL LAW PROVIDING FOR THE ADMINISTRATION AND ENFORCEMENT OF THE NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE A LOCAL LAW PROVIDING FOR THE ADMINISTRATION AND ENFORCEMENT OF THE NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE Local Law #2 of 2007. Be it enacted by the Town Board of the Town of Oswego,

More information

HSE guidelines. SApril 2017 WORK PERMITS

HSE guidelines. SApril 2017 WORK PERMITS HSE guidelines SApril 2017 WORK PERMITS Work safely or don t work at all There are strict procedures when working on installations and systems. After all, there s a risk for hazardous substances to be

More information

Coles Express Work Clearance: Induction for Contractors

Coles Express Work Clearance: Induction for Contractors Coles Express Work Clearance: Induction for Contractors Part of the Coles Online Contractor Induction system, for completion by contractors who will conduct works on Coles Express sites. Prerequisites

More information

SAFETY. EHS Pledge Vol 3 Issue 3 March 2017 RESPONSIBILITY. is everyone s STAY ALERT! Never dismiss a NEAR MISS

SAFETY. EHS Pledge Vol 3 Issue 3 March 2017 RESPONSIBILITY. is everyone s STAY ALERT! Never dismiss a NEAR MISS EHS Pledge Vol 3 Issue 3 March 2017 Accidents occur when we don t care SAFETY is everyone s RESPONSIBILITY Never dismiss a NEAR MISS A near miss is described as an unplanned event that did not result in

More information

THE CORPORATION OF THE MUNICIPALITY OF KINCARDINE BY-LAW NO BEING A BY-LAW IN RESPECT TO THE SALE AND USE OF FIREWORKS

THE CORPORATION OF THE MUNICIPALITY OF KINCARDINE BY-LAW NO BEING A BY-LAW IN RESPECT TO THE SALE AND USE OF FIREWORKS THE CORPORATION OF THE MUNICIPALITY OF KINCARDINE BY-LAW NO. 2017-135 BEING A BY-LAW IN RESPECT TO THE SALE AND USE OF FIREWORKS WHEREAS pursuant to the Municipal Act, 2001, S.O. 2001, c.25 as amended,

More information

EDITION. March 2011 WORK PERMITS. Health. Safety HSEW A WAY OF LIVING. Standards for professionals, be aware!

EDITION. March 2011 WORK PERMITS. Health. Safety HSEW A WAY OF LIVING. Standards for professionals, be aware! NL EDITION March 2011 H S E W A WAY OF LIVING Safety Health Well-being Environment HSEW Standards for professionals, be aware! Work safely or don't work Work Permits are used within NAM to govern how work

More information

Safe Work Permits Procedure

Safe Work Permits Procedure Launceston Airport Safe Work Permits Procedure Revision: 2 March 2015 APAL-SWP-001 Safe Work Permits Procedure Page 1 of 12 Table of Contents 1. Safe Work Permits... 3 1.1 Special Authorities... 4 1.2

More information

DRAFT Hot Work Procedure South Shore Regional School Board

DRAFT Hot Work Procedure South Shore Regional School Board Hot Work Procedure South Shore Regional School Board SSRSB Hot Work Procedure - 2010 Page 1 of 12 Introduction DRAFT Hot work comes in a variety of applications each with its own heat source severity.

More information

HSE - Permit to Work Procedure

HSE - Permit to Work Procedure Date Adopted: April 2016 Current Date: August 2016 Due for Review: August 2018 Division: HSE HSE - Permit to Work Procedure 1. SCOPE... 2 2. DEFINITIONS... 3 3. RESPONSIBILITIES... 5 4. PROCEDURE... 6

More information

DRAFT FOR CONSULTATION

DRAFT FOR CONSULTATION DRAFT FOR CONSULTATION Health and Safety at Work (Asbestos) Governor-General Order in Council At Wellington this day of 2015 Present: in Council Pursuant to sections 221 and 227 of the Health and Safety

More information

AUTORIDAD DEL CANAL DE PANAMÁ EXECUTIVE VICE PRESIDENCY FOR OPERATIONS

AUTORIDAD DEL CANAL DE PANAMÁ EXECUTIVE VICE PRESIDENCY FOR OPERATIONS AUTORIDAD DEL CANAL DE PANAMÁ EXECUTIVE VICE PRESIDENCY FOR OPERATIONS 3654-A (OPXI) ADVISORY TO SHIPPING No. A-28-2018 August 14, 2018 TO : All Shipping Agents, Owners, and Operators SUBJECT: Revision

More information

Public Input No. 17-NFPA 51B-2015 [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document

Public Input No. 17-NFPA 51B-2015 [ Global Input ] Statement of Problem and Substantiation for Public Input. Related Public Inputs for This Document of 55 11/18/2016 2:12 PM Public Input No. 17-NFPA 51B-2015 [ Global Input ] 3.3.X Responsible Party. The building owner, a lessee, or a duly authorized representative. Globally change "management" everywhere

More information

Supersedes: 1/17 (Rev.16) Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager. Revision Description Revised By Revision Date

Supersedes: 1/17 (Rev.16) Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager. Revision Description Revised By Revision Date Procedure No.: PA-020-0003 Page: 1 of 28 Port Arthur, TX. Reviewed: 05/18 Effective: 05/18 Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager Document Revision Change Table Revision

More information

The Group Chief Executive, Catalyst Housing Group, Tel hereby give you notice that I am of the opinion that at

The Group Chief Executive, Catalyst Housing Group, Tel hereby give you notice that I am of the opinion that at Improvement Notice Serial No. HSCP/11/01229 HEALTH and SAFETY at WORK etc. ACT 1974, Sections 21, 23, and 24 Name and address (see sec.46) To Of Mr Rod Cahill The Group Chief Executive, Catalyst Housing

More information

CHAPTER 1 GENERAL. 1

CHAPTER 1 GENERAL.  1 MINISTERIAL REGULATION ON THE PRESCRIBING OF STANDARD FOR ADMINISTRATION AND MANAGEMENT OF OCCUPATIONAL SAFETY, HEALTH AND WORK ENVIRONMENT IN CONFINED SPACE B.E. 2547 -------------------------------------

More information