CERTIFICATE OF ACCREDITATION In terms of section 22(2) (b) of the Accreditation for Conformity Assessment, Calibration and Good Laboratory Practice Act, 2006 (Act 19 of 2006), read with sections 23(1), (2) and (3) of the said Act, I hereby certify that:- SABS COMMERCIAL SOC LTD Co. Reg. No.: 2000/013581/30 ALTERNATIVE ENERGY AND FLUID TECHNOLOGY Facility Accreditation Number: T0196 is a South African National Accreditation System accredited facility provided that all conditions and requirements are complied with This certificate is valid as per the scope as stated in the accompanying schedule of accreditation, Annexure A, bearing the above accreditation number for MECHANICAL SAFETY & PERFORMANCE TESTING The facility is accredited in accordance with the recognised International Standard ISO/IEC 17025:2005 The accreditation demonstrates technical competency for a defined scope and the operation of a quality management system While this certificate remains valid, the Accredited Facility named above is authorised to use the relevant accreditation symbol to issue facility reports and/or certificates R Josias Chief Executive Officer Effective Date: 01 June 2016 Certificate Expires: 30 May 2021
Permanent Address of Laboratory: SABS COMMERCIAL SOC LTD Alternative Energy And Fluid Technology No1. Dr Lategan Road Groenkloof Pretoria, 0001 Postal Address: Private Bag X191 ANNEXURE A SCHEDULE OF ACCREDITATION Facility Number: T0196 Technical Signatories: Ms JJ van der Merwe (Rotodynamics) K Nxusa (Plumbing Components) MS Hlangwane (Plumbing Components) K Pitsi (Solar water systems) A Choma (Plumbing Components) Nominated Representative: Pretoria 0001 Tel: (012) 428 6748 Issue No.: 30 Fax: (012) 428 6703 Date of Issue: 01 June 2016 E-mail: johnson.marema@sabs.co.za Expiry Date: 30 May 2021 J Marema Materials / Products Tested 1. Plumbing Components 1.1 Water Taps Metallic bodies water taps Type of Tests / Properties Measured, Range of Measurement Standard Specifications, Techniques / Equipment Used SANS 226:2009 clause 4.6 & 4.7 SANS 226:2009 clause 5.2 SANS 226:2009 clause 5.3 Resistance to torque SANS 226:2009 clause 5.5 SANS 226:2009 clause 5.6 & 5.7 Resistance to bending SANS 226:2009 clause 5.8 Plastic bodies water taps SANS 1021:2007 clause 4.1.4 SANS 1021:2007 clause 5.2 SANS 1021:2007 clause 5.3 Resistance to torque SANS 1021:2007 clause 5.4 SANS 1021:2007 clause 5.5 & 5.6 Resistance to bending SANS 1021:2007 clause 5.7 SANS 1021:2007 clause 5.10 Single control mixer taps SANS 1480:2005 clause 3.2 SANS 1480:2005 clause7.1.2 & 7.9 SANS 1480:2005 clause 7.2.2.1 Page 1 of 6
resistance Resistance to bending SANS 1480:2005 clause 7.3 SANS 1480:2005 clause7.4 & 7.5 SANS 1480:2005 clause 7.6 SANS 1480:2005 clause 7.7 SANS 1480:2005 clause 7.9 Demand type water taps SANS 1808-66:2005 clause 4.1.1 SANS 1808-66:2005 clause 4.7 & 5.2 SANS 1808-66:2005 clause 5.3 Flexible Connectors SANS 1808-5:2010 clause 4.1.1 SANS 1808-5:2010 clause 5.2 SANS 1808-5:2010 clause 5.22 Drinking Fountain Taps SANS 1808-16: 2008 clause 4.1.1 SANS 1808-16: 2008 clause 4.8 & 5.2 SANS 1808-16:2008 clause 5.3 Metallic bodies metering taps and valves (Volume of discharge) SANS 1808-9:2008 clause 4.1.1 SANS 1808-9:2008 clause 4.4 & 5.2 SANS 1808-9:2008 clause 5.2 Electronically operated taps and valves SANS 1808-35:2010 clause 4.1.1 SANS 1808-35:2010 clause 5.2.2.5 SANS 1808-35:2010 clause 5.2.2.6 1.2 Water Valves Vent Valves Wedge gate and resilient seal valves for waterworks test Gate leakage test SANS 1532:2003 Clause 4.2.1 & 4.3, WI 7.1 SANS 664-1:2011 clause 5.2 SANS 664-1:2011 clause 4.4 SANS 664-1:2011 clause 5.3 SANS 664-2 & 3:2011 clause 6.2 Page 2 of 6
Gate strength test SANS 664-2 & 3:2011 clause 6.3 Wedge gate and resilient seal valves for general purposes Gate leakage Gate strength SANS 665-1:2011 clause 4.6 & 5.2 SANS 665-1:2011 clause 4.4 SANS 665-1:2011 clause 4.6 & 5.3 SANS 665-2 & 3:2011 clause 4.3 & 6.2 SANS 665-2 & 3:2011 clause 4.3 & 6.3 Copper alloy gate valves test Gate seat leakage test SANS 776:2005 clause 6.2.1 SANS 776:2005 clause 6.2.2 SANS 776:2005 clause 6.2 3 & 6.3.1 Fire- safe ball valves Hydrostatic pressure test SANS 1056-1:2008 clause 5.2 SANS 1056-1:2008 clause 3.5 SANS 1056-1:2008 clause 5.3 Heavy duty ball valves Hydrostatic pressure test SANS 1808-5:2010 clause 4.1.1 SANS 1808-5:2010 clause 5.2 SANS 1808-5:2010 clause 5.22 Light duty ball valves Hydrostatic pressure test SANS 1056-3:2008 clause 5.2 SANS 1056-3:2008 clause 4.4 SANS 1056-3:2008 clause 5.3 Check valves (flanged and water types): PN series Hydraulic test SANS 1551-1:2008 clause 8.1 SANS 1551-1:2008 clause 5.2 & 6.2 Cast steel gate valves SANS 191:2015 clause 5.2 SANS 191:2015 clause 4.4 Butterfly valves for general purposes SANS 1849:2008 clause 5.2 SANS 1849:2008 clause 4.5 Components of underground and above-ground hydrant systems Hydraulic pressure SANS 1128-1:2010 clause 6.5 & 7.2 Page 3 of 6
Capacity of valves SANS 1128-1:2010 clause 6.1 & 6.2 SANS 1128-1:2010 clause 7.1 1.3 Geysers Functional-control valves and safety valves for domestic hat and cold water supply systems Fixed electric storage heaters (geysers) Hydraulic test Vacuum & pressure test Resistance to fatigue Resistance to hydrostatic pressure SANS 665-1:2011 Clause 4.4, WI 7.21 SANS 198:2012 clause 4.3.10, 6.3 & 6.4 SANS 198:2012 clause 6.2 SANS 198:2012 clause 6.3.2 & 6.8 SANS 198:2012 clause 6.3 & 6.4 SANS 198:2012 clause 6.8 SANS 151: 2013 clause 6.3.2 SANS 151: 2013 clause 6.3.3 Drain cocks for hot-water storage containers Hydraulic pressure SANS 1808-53:2012 clause 5.2 SANS 1808-53:2012 clause 4.1.1 SANS 1808-53:2012 clause 4.2.6 SANS 1808-53:2012 clause 4.2.6 SANS 1808-53:2012 clause 4.2.4 SANS 1808-53:2012 clause 4.5 SANS 1808-53:2012 clause 4.2.7 Geyser drip trays Leak test SANS 1848:2011 clause 3.3, 3.4.1 & 3.4.3 SANS 1848:2011 clause 3.2 SANS 1848:2011 clause 4.2 In-line strainers Hydraulic pressure Head Loss and SANS 1808-58:2010 clause 5.2 SANS 1808-58:2010 clause 4.1.1 SANS 1808-58:2010 clause 4.6 SANS 1808-58:2010 clause 4.4.2 SANS 1808-58:2010 clause 4.5 1.4 WC Flushing Cisterns Float valves SANS 752:2009 clause 5.2 Page 4 of 6
SANS 752:2009 clause 5.4 SANS 752:2009 clause 5.5 SANS 752:2009 clause 5.7 Flush valves test Rate of discharge for a full flush Valve-type flush valve overflow valve SANS 1509:2008 clause 5.2 SANS 1509:2008 clause 5.4 SANS 1509:2008 clause 4.9.4. & 5.7 SANS 1509: 2008 clause 5.8 Automatic shut-off flush Flushing performance SANS 1240:2010 clause 4.4.2 & 5.4 SANS 1240:2010 clause 4.4.4 WC flushing cisterns Rate of discharge SANS 821:2007 clause 5.3 SANS 821:2007 clause 5.8 1.5 Cylinders Reliable welded steel gas cylinders Pressure (burst) test SANS 4706:2009 clause 9.2 1.6 Pipe Couplings & Fittings Copper based compression fittings Capillary solder fittings Copper tubes for potable water Copper tubes for medical gas and vacuum services Metallic compression type pipe couplings Pipe saddles SANS 1067-1:2005 clause 4.4 SANS 1067-1:2005 clause 5.2 SANS 1067-2:2005 clause 4.3 SANS 1067-2:2005 clause 5.2 SANS 460:2011 clause 4.4 SANS 460:2011 clause 4.5.7 SANS 1453:2011 clause 3.3 SANS 1453:2011 clause 3.4.7 SANS 1808-2:2013 clause 5.2.1 SANS 1808-2:2013 clause 4.6 SANS 1808-44:2010 clause 5.2 SANS 1808-44:2010 clause 4.1.1 SANS 1808-44:2010 clause 4.9.1 Page 5 of 6
SANS 1808-44:2010 clause 4.9.1 SANS 1808-44:2010 clause 4.5.2, 4.7 & 4.9.2 Pipe repair clamps SANS 1808-45:2013 clause 3.3 SANS 1808-45:2013 clause 3.3 SANS 1808-45:2013 clause 3.6 Flexible connectors 2. Solar water heaters Domestic solar water heaters Stagnation test Resistance to fatigue and hydrostatic pressure Resistance to rain Resistance to hail Resistance to freezing SANS 1808-5:2010 clause 5.2.1 SANS 1808-5:2010 clause 4.1.1 SANS 1808-5:2010 clause 4.2.7 SANS 1808-5:2010 clause 4.2.2 SANS 1808-5:2010 clause 4.2.3 & 4.2.4 SANS 1307:2014 clause 5.2 SANS 1307:2014 clause 5.3 SANS 1307:2014 clause 5.4 SANS 1307:2014 clause 5.5 SANS 1307:2014 clause 5.6 3.Rotodynamic Pumps Thermal performance using an outdoor test method Hydraulic performance acceptance tests Original Date of Accreditation: 30 October 2001 SANS 1307:2014 clause 5.9 ISO 9906:2012 ISSUED BY THE SOUTH AFRICAN NATIONAL ACCREDITATION SYSTEM Accreditation Manager Page 6 of 6