THALES AVIONICS ELECTRICAL SYSTEMS TECHNICAL PUBLICATION ATR 42/

Transcription

1 THALES AVIONICS ELECTRICAL SYSTEMS TECHNICAL PUBLICATION THALES - CUSTOMER SUPPORT DEPARTMENT - 41 boulevard de la République B. P. n CHATOU CEDEX - FRANCE Tel : Fax : monique.maximin@fr.thalesgroup.com 1

2 APPLICABLE TECHNICAL PUBLICATION 1. General conditions 2. List of LRU s 3. Details of evolutions 4. Statement of agreement 2

3 1. GENERAL CONDITIONS 2013 TAES TECHNICAL PUBLICATION CMM : Component Maintenance Manual. TCMS : Technical Characteristics Maintenance Sheet. : Service Bulletin : Service formation Letter Technical Publications (CMM) are available. To obtain the sale conditions, contact your Commercial Contact. Prior to the delivery of a CMM, the customer shall sign a Statement of Agreement. 2. LIST OF LRU S THALES vendor code TAES PN DESCRIPTION Electroni c Rotable Qty per plane Applicability F Transformer E 2 All F DC Generator Control Unit E 2 All F (-11) Hall Effect Current Sensor (HECS) E 5 All F DC Bus Power Control Unit E 1 All F Alternator R 2 All F Transformer (DPCT) E 3 All F0296 F A B C D AC Generator Control Unit E 2 All Static verter E 2 All F Emergency axe - 1 All F0296 F DC Starter Generator R 2 All AC Bus Power Control Unit E 1 All F0296 F11NA3121 Transformer Rectifier Unit E 1 F0296 F0296 F46BC0101 F46BD0101 F96GA0102 F96GA0101 F0296 B and ETOPS only Control Box E 1 All Landing Gear Control Lever E 1 All DC-STAR GSE - Direct Current System Tester Analyzer Recorder Ground Support Equipment E All 3

4 3. DETAILS OF EVOLUTIONS STARTER-GENERATOR PN CMM reference : Revision 10 : Date of update February, 09 th 2012 Brush and bearing Recommendation to operators in order to avoid abnormal MTBUR during brush and bearing Operation, Maintenance, storage, transportation, handling Rev.7 dated X dated Recommended scheduled maintenance X Rev. 3 dated Brush check procedure with SG fitted on engine X Rev.1 dated Brush procedure during brush X Rev. 2 dated Speed sensor tightening procedure. Brush and bearing without disassembly of the SG. During each speed sensor assembling operation during brush and bearing X Rev 1 dated X dated Packaging for Starter Generator Recommended for shipment X dated Armature information Recommended X dated Checking of the torque shaft Recommended X dated Recommended dated

5 Second source of Anti-flash varnish Recommended dated Amendment A, B & C Do not exist for this unit Amendment D Recommended dated Amendment E & Recommended during overhaul dated Amendment F dated Amendment G 1994 Amendment H X dated Amendment J X dated Amendment K During overhaul X dated scheduled maintenance On customer request X dated Amendment M Conformity during overhaul X dated Amendment N X dated Overhaul procedure during overhaul X dated Amendment P Component X dated Amendment R X dated

6 STARTER-GENERATOR PN CMM reference : Revision 10 : Date of update February, 09 th 2012 Brush and bearing Recommendation to operators in order to avoid abnormal MTBUR during brush and bearing Operation, Maintenance, storage, transportation, handling Rev.7 dated X dated Recommended scheduled maintenance X Rev. 3 dated Brush check procedure with SG fitted on engine X Rev.1 dated Brush procedure during brush X Rev. 2 dated Speed sensor tightening procedure. Brush and bearing without disassembly of the SG. During each speed sensor assembling operation during brush and bearing X Rev 1 dated X dated Packaging for Starter Generator Recommended for shipment X dated Armature information Recommended X dated Checking of the torque shaft Recommended X dated Recommended dated Second source of Anti-flash varnish Recommended dated

7 Amendment A X dated Amendment B X dated Amendment D Conformity during overhaul X dated Amendment E X dated Overhaul procedure during overhaul X dated Amendment F Component X dated Amendment G X dated AC GENERATOR PN CMM reference : Revision 4 : Date of update May, 30th 2008 Verification of measurement Under repair X dated Verification of torque value On aircraft Under repair dated Under repair (overhaul or bearing ) dated Recommended dated

8 Amendment A Component dated Amendment B Amendment C Amendment D Amendment E Amendment F repair procedure During repair of rotating diodes bridges. Under repair only if rewinding of stator is necessary On customer request or if component has to be replaced (P058137) Recommended On customer request or if component has to be replaced (P or P058137A) dated dated Amendment G Amendment H Amendment J & assembly procedure. & assembly procedure. Qualification of a new source. (Diode-holder plate assy.) dated dated dated Rev 1 dated Amendment K dated

9 AC GCU PN CMM reference : Revision 4 : Date of update September, 30th 1999 Recommended dated Recommended dated Amendment A during repair by OEM only dated Amendment B during repair by OEM only dated Amendment C Amendment D Component during repair Systematically during repair if PCB Z500 must be replaced dated Amendment E Dated dated Modification for version (new propeller). On customer request dated

10 AC GCU PN CMM reference : Revision 4 : Date of update September, 30th 1999 Mechanical check of the rear guide bushing. Under repair dated Recommended dated Recommended dated Amendment A Component Systematically during repair if PCB Z500 must be replaced dated Amendment B dated DC GCU PN CMM reference : Revision 2 : Date of update July, 5th 2006 Mechanical check of the rear guide bushing. Under repair dated

11 Recommended dated Recommended dated Amendment A Amendment B Amendment C Amendment D Amendment E Recommended dated dated dated dated Rev. 2 dated Amendment F On customer request or if PCB has to be repaired dated Amendment G Component selector switch or PCB has to be replaced dated AC BPCU GCU PN CMM reference : Revision 3 : Date of update June, 15th 1999 Recommended dated

12 Recommended dated Amendment A ated On customer request dated AC BPCU GCU PN CMM reference : Revision 3 : Date of update June, 15th 1999 Mechanical check of the rear guide bushing dated Recommended dated Recommended dated

13 DC BPCU PN CMM reference : Revision 3 : Date of update August, 8 th 2006 Amendment A Recommended Recommended dated dated dated Amendment B dated Amendment C manufacturing process dated Amendment D dated Amendment E dated Amendment F dated Amendment G 1993 Amendment H dated Amendment J PCB has to be replaced Amendment K dated

14 Amendment L 1999 Amendment M Component 2001 Amendment N dated Amendment P Component dated On customer request dated DC BPCU PN CMM reference : Revision 3 : Date of update August, 8 th 2006 Mechanical check of the rear guide bushing dated Recommended dated Recommended dated

15 Amendment G On customer request Amendment H 1994 Amendment J dated Amendment K PCB has to be replaced Amendment L dated Amendment M Amendment N Component Amendment P Component dated Amendment R dated Amendment S Component dated

16 STATIC INVERTER PN A CMM reference : Revision 2 : Date of update June, 15th 2001 Amendment A Amendment B Amendment C Checking of overvoltage threshold protection the control of "Static verter fault" signal of auxiliary power card Amendment D Component C in order to avoid double loss of static inverter Under repair Recommended Recommended during repair during repair during repair during repair B dated dated dated A dated AB dated STATIC INVERTER PN B CMM reference : Revision 2 : Date of update June, 15th 2001 Recommended dated

17 Amendment B Component D in order to avoid double loss of static inverter Recommended during repair dated AB dated STATIC INVERTER PN C CMM reference : Revision 2 : Date of update June, 15th 2001 Recommended Recommended dated dated STATIC INVERTER PN D CMM reference : Revision 2 : Date of update June, 15th 2001 Recommended Recommended dated dated

18 TRU PN F11NA3121 CMM reference : Revision : Date of update October, 15th 1996 Recommended Recommended dated dated LIGHTING TRANSFORMER PN 156 Technical Characteristics & Maintenance Sheet reference : Revision 3 : Date of update April, 2010 CONTROL BOX PN F46BC0101 CMM reference : Revision 1 : Date of update December, 01st 1993 Recommended Recommended dated dated

19 Amendment A Amendment B and functionning. manufacturing & repair processes.. necessary F46BC dated Amendment C Amendment D spection of the fan control box Unit in operation necessary. necessary F46BC dated CONTROL BOX PN F46BD0101 CMM reference : Revision : Date of update June, 15th 2001 Recommended Recommended dated dated Amendment A. under production LANDING GEAR CONTROL LEVEL PN F96GA0101 CMM reference : Revision 2 : Date of update January, 26th 2009 Recommended dated

20 LANDING GEAR CONTROL LEVEL PN F96GA0102 CMM reference : Revision 2 : Date of update January, 26th 2009 Amendment A functionning Recommended dated Amendment B On customer request Amendment C On customer request F96GA dated Amendment D functionning TRANSFORMER (DPCT) PN (DPCT : Differential Protection Current Transformer) Technical Characteristics & Maintenance Sheet reference : Revision 2 : Date of update June,

21 HALL EFFECT CAPTOR SENSOR PN Technical Characteristics & Maintenance Sheet reference : Revision 4 : Date of update April, 2006 Amendment A under production 1998 Amendment B under production 2003 EMERGENCY AXE PN Technical Characteristics & Maintenance Sheet reference : Revision 1 : Date of update 1992 Packaging for Emergency axe Recommended for shipment dated DC-STAR GSE PN B USER MANUAL : Y Revision a : Date of update October, 17 rd

22 4. STATEMENT OF AGREEMENT Statement of Agreement to Terms and Conditions of Sale of Thales Technical Publications Thales Component Maintenance Manual 24-XX-XX is intended solely for use by Company Name. Copying, reproducing or redistribution of this or any Thales Component Maintenance Manual (CMM) or Service Bulletin (), to any other party or location is strictly prohibited without Thales prior written consent. Thales retains all intellectual property rights, title and interest in the CMMs andor s provided, including all rights under applicable patents, copyrights, trademarks and trade secrets, and all renewals and extensions thereto. Company Name shall not alter or remove any patent, copyright, trademark, or proprietary rights notice. Agreed to and Accepted by: (Print Name) (Signature) (Title) (Date) 22